Category Archives: XYZ-Theta

Motion Control – Low Profile, High Precision Motorized Cross Roller Linear Stages

Motion Control – Precision Linear Stage

motion control - linear stage
motion control - stage

 

Van Nuys, CA – Optimal Engineering Systems, Inc. (OES) offers a high precision series of low cost, low profile motorized single axis positioning stages. The compact AQ110 Series of four cross roller linear stages have travel lengths of 15 mm (0.590 in), 30 mm (1.181 in), 50 mm (1.968 in), and 75 mm (2.952 in). Open loop repeatability of all stages is 0.5µ using a 10 mirco- steps-per-step Step Motor Driver or just 0.25µ using a 20 mirco-steps-per-step Step Motor Driver. Precision ground lead screws with just 2µ of backlash and high precision cross roller linear travel guides assures repeatability of 5µ, and positional accuracy of 10µ.

 See the YouTube Video: https://youtu.be/qRsjeChhEWo

Innovations in Motion Control – XY-Theta Alignment Stages Feature: Sub Micron Resolution!

Innovations in Motion Control –

  XY-Theta Alignment Stages!

Innovations in Motion Control - alignment stages
motion control - stages - custom

 

 

Van Nuys, CA – — Innovations in Motion Control Technology  – Two new XY-Theta Alignment Stages have been released by Optimal Engineering Systems, Inc. (OES). The XYR-15-60-01 and the XYR-15-60-04 Alignment Stages feature 15 mm (0.58 in.) of travel in both the X and Y axes and 360 degrees of continuous rotation on the rotary axis. The new XY-Theta Alignment Stages are driven by Two Phase Stepper Motors featuring 0.25 micron resolution (20 Micro-steps per Step Motor Driver in use).

Motion Control – New! Large Three-axis Gimbal Mounts Feature High Resolution, and Four Motor Options

Motion Control – Solenoid Drivers

motion control - gimbal mount
motion control - stage

 

 

 

Van Nuys, CA – Motion Control – Designed for larger cameras, tracking devices, telescopes, optics, and other devices, four new, high resolution, three axis gimbal mounts have been released by OES (Optimal Engineering Systems, Inc.). This new series of Three Axis Gimbal Mounts are 588 mm wide by 463 mm high, and handle loads up to 10 kg. The AU400-AER (Azimuth, Elevation, and Roll) Series of Three Axis Gimbal Mounts feature high precision 180:1 worm gear driven “V” groove rotary stages.

Motion Control – NEW! A Series of 600 mm to 1000 mm High Precision Ball Bearing Linear Guide Stages Available from OES!

Motion Control – Long Travel Linear Stages

motion control - linear stagemotion control - OES

 

 

 

Van Nuys, CA – — Motion Control – A series of long travel, low cost, low profile, motorized, profile rail positioning stages are now available from Optimal Engineering Systems, Inc. (OES). The AQ140 Series of linear stages are available off-the-shelf in travel lengths of: 600 mm, 700 mm, 800 mm, 900 mm, and 1000 mm. These high precision stages can be ordered with a Two-Phase Stepper Motor (pictured) which feature resolutions of 2 micron and 1.25 micron (achieved with a 10 or 20 micro-steps per step stepper motor driver), and up to 80 mm per sec of travel.

Motion Control – New! Three-axis Gimbal Mounts Feature High Resolution, High Load Capacity, Stability, and Four Motor Options!

Motion Control –  Three-Axis Stage!

motion control - three-axis stage


motion control - stages - custom

 

 

 

Van Nuys, CA – — Motion Control – Four high resolution, high Load, high stability three axis gimbal mounts have been released by OES (Optimal Engineering Systems, Inc.). These four new AU270-YPR Three Axis (Yaw, Angular Pitch, and Roll) Gimbal Mounts were developed to be used with larger and heavier: Cameras, telescopes, directional antennas, optics, lasers, tracking and scanning systems. These new, larger, high stability, gimbal mounts are 400 mm wide x 480 mm high, weigh 50 kg and handle loads up to 10 kg and the Roll Axis features a large 90 mm thru hole for cables and optics.

Motion Control – High Precision, High Load Goniometer Stages with +/- 30 Degrees of Travel Are Available from OES!

XYZ-G Positioning Stage – XYZ-Goniometer Positioning Stages

Motion Control goniometer stage
motion control - stage

 

Van Nuys, CA – – Motion Control – Optimal Engineering Systems, Inc. (OES) has added four goniometers to their expanding catalog of high precision positioning stages. The new, AK160-30 Goniometer Series feature precision ground worm gears with a 400:1 ratio and pre-loaded cross roller guides offer +/- 30 degrees of travel with 30 kg of load.

Motion Control – XY Alignment Stage Featuring High Resolution and High Repeatability Available from OES!

Motion Control – XY Alignment Stage
 Motion Control - OES Alignment Stage

motion control - OES Logo

 

 

Van Nuys, CA – — Motion Control – The AU200-50×50-SC Alignment Stage from Optimal Engineering Systems, Inc. (OES) is a high resolution, high repeatability XY stage for such applications as: alignment, assembly, laser drilling, machining, medical, industrial, semiconductor handling, testing, scanning, and optical applications. The linear travel of the X and Y axes is 50 mm x 50mm, and the resolution of each axis is 5 microns (non-micro-step) or 0.125 microns (with 20 micro-steps per step motor driver in use), repeatability is 1.5 microns, and positional accuracy is 5 microns.