Category Archives: Latching

Motion Control – Rotary Solenoids Matched to An Application Are Available in OEM Quantities!

Motion Control – Rotary Solenoids

motion control - rotary solenoid

Motion Control – Van Nuys, CA – The R-09-150 CWN Series of Clockwise, Reverse Shaft Extension Rotary Solenoids from Magnetic Sensor Systems (MSS), available in OEM quantities, features 18 different winding configurations allowing the user to match torque and duty cycle requirements to an application.

motion control - mss logo blk

These compact 38.1 mm (1.50 in.) diameter motion control solenoids are just 22.1 mm (0.87 in.) long and have two M4X0.7 threaded studs (8-32 studs optional) 7.4 mm (0.29 in.) long on a 22.2 mm (0.875 in.) bolt circle. The reverse shaft has 40 degrees of clockwise rotation, extending 13.0 mm (0.51 in.). Shaft end is serrated for better grip of the attached load.

Motion Control – Select from a Series of Compact Electromagnets to Meet Holding Force and Duty Cycle Requirements of an Application!

Motion Control – Electromagnets

motion control - electromagnet

Motion Control – Van Nuys, CA – A powerful series of compact, low cost electromagnets has been released by Magnetic Sensor Systems (MSS). Their E-22-150 Series of Tubular Electromagnets 1.5 in. in diameter x 2.15 in. feature 19 different windings to select from based on the duty cycle and holding force requirements of the application. E-22-150 Electromagnets are immediately available off-the-shelf in sample quantities and OEM quantities for Just-In-Time deliveries.

motion control - mss logo blk

Depending on the application, duty cycle, and required force, the electromagnets in this series can supply 54 to 83 lbs. of holding force for duty cycles ranging from 100% (continuously on) to 10%.

Motion Control – Meet the Voltage, Duty Cycle, and Force Requirements of Many Applications with a Series of 18 Push Type Open Frame Solenoids with a 1 Inch Stroke!

Motion Control – Push Type Open Frame Solenoid

motion control - open frame solenoid

 

 

motion control - mss logo blk

 

Motion Control Solenoids – Van Nuys, CA — Push Type Solenoids from Magnetic Sensor Systems (MSS) includes a series of 18 different low-cost open frame solenoids to select from based on the Voltage, Duty Cycle, Force of up to 96 oz (26.7 N) and stroke requirements of the user. These clean, high efficiency, low-cost motion control S-18-100-QH Open Frame Push Type Solenoids can be operated at a variety of duty cycles (voltage dependent) and are the ideal choice for: Medical dispensing, mixing, valve control, disconnects, vending machines, farm machinery, transmission shifting, fire suppression systems, cabinet locks, door controls, assembly and sorting equipment.

Motion Control – The S-63-38 Series of 0.38 Inch Dia. Pull Type Solenoids Features 16 Standard models to Meet Voltage, Duty Cycle, Force, and Stroke Requirements of an Application!

Motion Control – Tubular Solenoids

motion control - solenoid
Motion Control – Van Nuys, CA – The S-63-38 Series of Pull Type Tubular Solenoids has been released by Magnetic Sensor Systems (MSS). This series of 0.38 in. diameter motion control solenoids features 16 standard off-the-shelf solenoids to select from based on the Voltage, Duty Cycle, Force and Stroke requirement of the user.

motion control - mss logo blk

These miniature motion control solenoids featuring a 0.38 in. diameter have a 0.66 in. long housing and when retracted are just 0.80 in. long.

Motion Control – Select the Low Cost, Economical, Bi-Directional Latching Solenoid Best Suited for an Application!

Motion Control – Latching Solenoids

motion control - latching solenoids
Motion Control – Van Nuys, CA –Latching Bi-Directional Solenoids released by Magnetic Sensor Systems (MSS) are low cost, economical to use, and easy to integrate into an application. The S-18-100LC2 and S-18-100LF2 Latching Bi-Directional Solenoids feature the same compact dimensions: 1.00 in. wide x 0.84 in. high x 1.73 in. long with 6-32 threaded Push/Pull plungers. 

motion control - mss logo blk

The plungers have a travel of 0.19 in. and in the extended position are 0.50 in. long, two 8-32 (or optional M4) threaded mounting holes are located on the underside of the solenoids.

Motion Control – Open Frame Series of 18 Pull Type Solenoids with a 1 Inch Stroke Can Meet the Voltage, Duty Cycle, and Force Requirements of Many Applications!

Motion Control – Open Frame Solenoids

motion control - open frame solenoids
Motion Control – Van Nuys, CA – The S-18-100 Series of Open Frame Pull Type Solenoids from Magnetic Sensor Systems (MSS) includes 18 different solenoids to select from based on the Voltage, Duty Cycle, Attractive Force (up to 100 oz) and Stroke requirements of the user. MSS Solenoid coils typically utilize 23 to 40 AWG (American Wire Gauge) windings with Class “F” insulation for better protection of the solenoid during longer duty cycles.

motion control - mss logo blk

The S-18-100 Series solenoids are 1.000 in. wide x 0.84 in. high x 1.74 long and have a 1.00 stroke. The noncaptive plunger or actuator is 0.312 in. in diameter with a clevis end for load attachment.

Motion Control – Select from the S-70-300H Series of 3 Inch Dia. Push Type Solenoids to Meet the High Force Requirements of an Application!

Motion Control – Push Type Solenoids

motion control - push type solenoid
Motion Control – Van Nuys, CA – Solenoids – The S-70-300H Series of high force Push Type Tubular Solenoids has been released by Magnetic Sensor Systems (MSS). Ideal for strokes of up to 4.00 inches, this series of solenoids features 18 different solenoids to select from based on the Force, Voltage, Duty Cycle, and Stroke requirement of the user. MSS Solenoids coils typically utilize Class “F” 23 to 40 AWG (American Wire Gauge) windings with Class “A” lead wire insulation for better protection of the solenoid during longer duty cycles.

Solenoids - mss logo blk

The S-70-300H Series of solenoids feature a 3.000 in. diameter x 7.00 in. long housing and a 1.75-12 UN A thread for mounting.